ZS1130 30HP Diesel Engine Specifications and Compatibility Guide

17, Nov. 2026

 

ZS1130 30HP Diesel Engine Specifications and Compatibility Guide

The ZS1130 30HP Diesel Engine is identified by its 30-horsepower output, equivalent to approximately 22.4 kW. That rating alone does not confirm that the engine will fit or operate correctly in your machine: compatibility also depends on rated speed, mounting dimensions, output-shaft details, cooling arrangement, and the driven equipment’s load. Use the engine nameplate and a supplier’s current technical drawing to verify these details before ordering. This guide explains what to check and what information to provide when sourcing a replacement or planning an equipment build.

If you want to learn more, please visit our website.

Key Takeaways

  • The stated output is 30 hp, or approximately 22.4 kW; confirm the rating conditions and rated speed for the offered unit.
  • Match the engine to the machine by dimensions and operating requirements, not by model designation alone.
  • Check mounting, shaft or coupling, rotation, cooling, fuel, controls, and accessory requirements before purchase.
  • Ask suppliers to confirm the exact configuration, included components, order quantity, and delivery estimate in writing.

Who This Guide Is For

This guide is intended for agricultural machinery manufacturers, replacement-parts buyers, equipment repair businesses, and importers evaluating a ZS1130 30HP diesel engine. It is useful when replacing an existing engine, specifying a new machine, or comparing supplier quotations. Buyers should treat model names as a starting point rather than a complete engineering specification. Final suitability depends on the application and the exact version being offered.

Understanding the Engine Specification

What the 30HP Rating Tells You

Horsepower describes power output, while the equivalent metric figure is about 22.4 kW. These values do not state the engine’s torque at every speed, its fuel consumption, or the power available under all operating conditions. Those details depend on the manufacturer’s rating method and the specific engine configuration. Request the rated speed and applicable performance data for the offered model before comparing it with a machine requirement.

Configuration and Specification Details to Confirm

The product information supplied for this guide associates the ZS1130 with a single-cylinder, water-cooled diesel engine category. Confirm that the quotation describes the same configuration you need, because product listings and model designations may not fully specify each supplied version. Ask for a datasheet or drawing that identifies the offered unit rather than assuming that every engine carrying a similar designation has identical fittings. This is especially important when ordering replacement parts or planning a direct installation.

Specification area What to verify Why it matters
Power and speed Rated output, rated speed, and rating conditions Confirms whether engine output suits the driven machine
Mounting Base dimensions, hole spacing, and mounting orientation Determines whether the engine can be secured without unplanned fabrication
Power take-off Shaft diameter, length, keyway or coupling, and rotation Checks the connection to a pump, gearbox, or other load
Cooling and exhaust Cooling-system arrangement, radiator or water connections, and exhaust outlet Helps prevent packaging and operating conflicts
Controls and accessories Starting method, control connections, charging equipment, and included parts Clarifies what is needed for installation and operation

Application Matching and Compatibility

Match the Engine to the Machine’s Load

Start by identifying what the engine will drive, such as an agricultural machine, pump, or other equipment. Record the load’s required power and operating speed, then compare them with the engine’s documented output and speed range. A 30 hp label is not enough to establish a suitable match if the machine needs a particular torque profile or operates at a different speed. Where the equipment has a gearbox or belt drive, include its ratio and operating requirements in the review.

Check Physical and Connection Interfaces

Compare the engine’s mounting points with the machine frame and check the shaft or coupling against the driven component. Record dimensions in millimetres, including shaft diameter, usable shaft length, and mounting-hole spacing, and send those measurements to the supplier for confirmation. Also check rotation direction, alignment, available clearance, and the position of exhaust and cooling connections. A mismatch may require adapters or fabrication, which can affect cost, installation time, and service access.

If you want to learn more, please visit our website YUANGEN.

Review Cooling, Fuel, and Electrical Requirements

Confirm whether the machine is designed for the cooling arrangement of the offered engine and whether the installation has room for the required components and airflow. Check the fuel connection, controls, starting arrangement, and electrical requirements against the existing system. Do not assume that a replacement engine includes a radiator, battery, wiring, control panel, or other accessories unless the quotation lists them. Ask the supplier to distinguish between standard supply and optional items.

A Practical Selection Framework

  1. Document the application: Record the machine type, duty, driven load, and expected operating conditions.
  2. Collect the existing engine details: Photograph the nameplate and note its model, rated output, speed, and connection information where available.
  3. Measure the interfaces: Record mounting and shaft dimensions in millimetres, and note rotation direction and clearance limits.
  4. Compare confirmed specifications: Use a supplier datasheet or drawing to check power, speed, cooling, starting, and accessory requirements.
  5. Resolve differences before ordering: Ask about adapters, configuration options, included parts, and any installation changes the machine may need.

This process helps separate a genuine fit from a superficial model-number match. If a critical value is missing, mark it as unconfirmed instead of assuming it matches the old engine. Share the machine’s requirements with the supplier and request written confirmation against the offered configuration. For unusual installations, review the drawing with your engineering or maintenance team before approving an order.

Pricing, MOQ, and Lead Time

Price and delivery depend on the exact configuration, order quantity, requested accessories, packaging, and shipping destination. Minimum order quantity and lead time can also vary by supplier and availability, so they should be confirmed for each quotation rather than inferred from a product page. Ask whether the price covers the engine only or includes specified accessories and export packaging. Request the quotation to state the model configuration, quantity, production or dispatch estimate, payment terms, and any parts supplied separately.

Supplier Evaluation Checklist

A suitable supplier should be able to identify the engine configuration being quoted and provide relevant technical information for compatibility review. Ask for a current specification sheet, dimensional drawing, and clear photographs or descriptions of the mounting and output interfaces where available. Confirm what inspection or documentation is included with the order, without assuming certifications or test records that have not been provided. Also establish how the supplier handles spare-parts inquiries and technical questions after shipment.

  • Does the quotation specify the exact engine configuration and rated output?
  • Can the supplier confirm key dimensions and connection details against your machine?
  • Are included components, optional accessories, MOQ, and lead time clearly stated?
  • Is there a clear contact for technical clarification and parts support?

Conclusion: Confirm Fit Before You Buy

The ZS1130 30HP diesel engine is identified by a 30 hp rating, approximately 22.4 kW, but compatibility cannot be determined from that figure alone. Confirm rated speed, mounting dimensions, shaft or coupling, rotation, cooling, controls, and the accessories included in the offered configuration. The most practical next step is to send your machine details, existing engine nameplate, and measured interfaces to the supplier and request a written match against a current drawing. YUANGEN can review your application requirements and provide a quotation based on the configuration, quantity, and delivery destination you specify.

Want more information on ZS1130 30HP Diesel Engine? Feel free to contact us.