2.36 inch ss304 welded wire mesh panel specifications and buying guide

18, Nov. 2026

 

2.36 Inch SS304 Welded Wire Mesh Panel Specifications and Buying Guide

A 2.36 inch SS304 welded wire mesh panel is a flat grid made by resistance-welding stainless steel wires at their intersections, with “2.36 inch” typically referring to the nominal mesh opening or spacing. Before ordering, confirm whether that measurement means the clear gap between wires or the center-to-center pitch, since the wire diameter affects the difference. The conversion is 2.36 in = 59.944 mm, commonly rounded to 59.94 mm; the standard conversion is 1 in = 25.4 mm. For an accurate quotation, define the opening, wire diameter, panel dimensions, finish, quantity, and any tolerances in one specification.

You can find more information on our web, so please take a look.

Key Takeaways

  • Confirm what “2.36 inch” measures: clear aperture or center-to-center spacing.
  • Specify SS304, wire diameter, panel width and length, edge condition, and surface finish.
  • Match the mesh opening and wire thickness to the required containment, airflow, strength, and environment.
  • Ask suppliers to confirm tolerances, packaging, minimum order quantity, and lead time for the exact configuration.

Who This Guide Is For

I prepared this guide for purchasing teams, engineers, fabricators, and distributors sourcing stainless steel welded mesh panels for industrial or commercial use. It is useful when a drawing, project specification, or existing part calls for a nominal 2.36 inch mesh dimension but does not explain the measurement convention or panel details. If you are comparing quotations, use the checklist below to ensure suppliers are pricing the same product. Where an application has safety, structural, or regulatory requirements, confirm the design with the responsible engineer or project authority.

Understanding the Product and Its Specifications

What “2.36 inch SS304 welded wire mesh panel” means

“SS304” identifies the requested stainless steel grade, while “welded wire mesh” describes wires joined at their intersections to form a grid. “Panel” indicates a cut, flat section rather than a continuous roll, although panel dimensions and edge details still need to be stated. The 2.36 inch figure describes a nominal mesh dimension, but buyers should not assume it is the clear opening unless the drawing or supplier confirms that interpretation. A complete purchase specification therefore includes more than the grade and nominal spacing.

Specifications to confirm before requesting a quote

Specification What to define Why it matters
Mesh dimension Clear opening or center-to-center spacing; square or rectangular layout Determines the actual gap and grid geometry
Wire diameter Required wire diameter, stated in mm or another agreed unit Affects open area, mass, rigidity, and fit with the application
Panel size Finished width and length, with units and dimensional tolerances Supports fit-up, installation, packing, and freight planning
Material SS304 and any required material documentation Helps align the supplied material with project requirements
Edges and finish Cut or finished edges, surface condition, and any post-weld treatment requested Influences handling, appearance, and fabrication requirements

These details are interdependent. For example, a larger wire diameter can reduce the clear opening if the pitch remains fixed, while a clear-opening specification may require a different pitch for the same wire diameter. Panel size and edge treatment can also affect manufacturing and packing choices. I recommend asking the supplier to repeat the agreed dimensions in the quotation or drawing rather than relying on a product name alone.

Applications and Material Considerations

SS304 welded mesh panels may be considered for guards, partitions, equipment enclosures, racks, screens, and fabricated components where a rigid open grid is suitable. The 2.36 inch spacing is relatively open compared with fine filtration mesh, so it is generally not a choice for retaining small particles or providing a close barrier. Suitability depends on the object being contained, the expected load, the support spacing, and the environment. For load-bearing or personnel-protection uses, the panel must be assessed against the project’s engineering requirements rather than selected by mesh size alone.

SS304 is a common stainless steel specification, but the grade name by itself does not establish that a panel is suitable for every corrosive or hygienic environment. Exposure to chemicals, salts, cleaning agents, temperature, and moisture can influence material selection and maintenance needs. If the installation is near marine conditions or aggressive chemicals, ask the design authority whether another alloy or a different finish is required. Also confirm any requirements for material traceability or documentation before placing the order.

How to Select the Right Panel

Step 1: Define the opening correctly

Write down whether 2.36 inch means clear opening or wire center-to-center spacing. If a drawing is available, mark the measurement directly on it and identify the direction of each mesh dimension. Confirm whether the grid is square or rectangular and whether the spacing applies in both directions. This simple clarification helps prevent a panel that looks similar by name but does not meet the installation or containment need.

Link to Shunqiang Wire Mesh

Step 2: Set wire and panel dimensions

Choose wire diameter based on the required rigidity, open area, handling, and fabrication method, using engineering guidance where loads or safety are involved. State finished panel width and length, along with the allowed dimensional variation and edge condition. If panels must fit into a frame, provide the frame’s usable internal dimensions and explain how the mesh will be retained. Do not assume that a supplier’s standard panel size or edge configuration will suit your assembly.

Step 3: Check the environment and finish

Describe where the panel will be installed and what it will contact, including cleaning chemicals or outdoor exposure where applicable. Specify the required surface condition and whether the project needs documentation for the material or manufacturing process. If the panel will be welded, bent, cut, or coated after delivery, share that information so the supplier can consider it when reviewing the specification. Final compatibility should be checked against the actual operating conditions.

Step 4: Compare quotations on the same basis

Request written confirmation of grade, mesh measurement convention, wire diameter, panel dimensions, quantity, tolerances, finish, and packaging. Compare quoted prices only after verifying that these details match, since a change in wire diameter or panel size can change material use and processing. Ask each supplier to state the minimum order quantity, production lead time, shipping basis, and any charges that are excluded. If a specification is still being developed, request a technical review before approval.

Pricing, MOQ, and Lead Time

The price of a 2.36 inch SS304 welded wire mesh panel depends on the material, wire diameter, panel dimensions, order quantity, processing, packaging, and delivery requirements. Custom dimensions, special edge treatment, or additional documentation may influence the quotation, but the impact varies by supplier and order. Minimum order quantity and production lead time are likewise configuration- and schedule-dependent, so they should be confirmed in writing rather than assumed from a general product listing. For an actionable quote, send a drawing or specification, quantity, destination, and required delivery date.

Supplier Evaluation Checklist

  • Can the supplier confirm whether the mesh dimension is clear opening or center-to-center pitch?
  • Does the quotation list SS304, wire diameter, panel size, tolerances, and edge condition?
  • Can the supplier review a drawing and identify specification gaps before production?
  • Are MOQ, lead time, packaging, shipping terms, and required documents stated clearly?
  • Can the supplier explain how any proposed substitution differs from the requested specification?

As Shunqiang Wire Mesh, we encourage buyers to provide a complete requirement rather than relying on the phrase “2.36 inch SS304 mesh panel” alone. We can review the requested mesh description and panel details for quotation, and clarify which information is needed to evaluate the configuration. Please share the intended application, drawing or dimensions, quantity, and destination so we can respond on a comparable basis. Any proposed material or dimensional change should be reviewed and approved by the buyer before production.

Conclusion: What to Do Before Buying

A 2.36 inch SS304 welded wire mesh panel can be specified effectively when its mesh measurement, wire diameter, panel dimensions, material, finish, and edges are all defined. The first step is to establish whether 2.36 inch means the clear aperture or the center-to-center spacing; then confirm the panel geometry against the application and installation. Do not treat the grade or nominal opening as proof that the panel is suitable for a particular load or environment. Send a drawing or written specification to Shunqiang Wire Mesh and request confirmation of the product details, MOQ, lead time, and quotation assumptions before placing an order.

The company is the world’s best 2.36 inch ss304 welded wire mesh panel supplier. We are your one-stop shop for all needs. Our staff are highly-specialized and will help you find the product you need.