A 2.36 inch SS304 welded wire mesh panel is a rigid panel made by resistance-welding stainless steel 304 wires at regular intersections, with an opening specified as approximately 2.36 inches. Since 2.36 inches equals 59.944 millimeters, buyers may also see this size described commercially as a 60 mm opening. The final panel specification still depends on wire diameter, panel length and width, edge treatment, tolerances, quantity, and surface condition.
If you are looking for more details, kindly visit our website.
I recommend treating “2.36 inch” as the opening size only, not as a complete product specification. Before ordering, I confirm whether the opening is measured from wire center to wire center or from the clear space between wires. At Shunqiang Wire Mesh, we use the buyer’s drawing, specification sheet, or approved sample to align mesh opening, wire diameter, panel size, and stainless steel grade before production.
This guide is intended for importers, distributors, fabricators, contractors, equipment manufacturers, and procurement teams purchasing stainless steel welded wire mesh panels in commercial quantities. It is especially useful when a project requires an open grid with greater dimensional stability than loose woven mesh. It also helps buyers compare quotations that appear similar but use different measurement methods or material descriptions.
The panel may be used for guards, partitions, infill, cages, racks, machine protection, architectural screens, and general fabrication. The correct selection depends on load, environment, appearance, installation method, and local compliance requirements. A large opening such as approximately 60 mm should not automatically be treated as suitable for every safety application, because the required retention and access control level may demand a smaller opening.
Welded wire mesh is formed when longitudinal and transverse wires are arranged in a grid and joined at their crossing points. In this guide, the nominal opening is 2.36 inches, or approximately 60 mm. The opening can be specified by center-to-center pitch or clear opening, so the purchasing document should state the method clearly.
Wire diameter affects the clear opening, panel weight, stiffness, welding requirements, and total material consumption. For example, a 60 mm center-to-center spacing will produce a smaller clear opening after the wire diameter is considered. I therefore recommend requesting both the nominal pitch and the intended clear opening when the mesh is used for guarding, screening, or controlled access.
SS304 is an austenitic stainless steel grade widely selected for general corrosion resistance, cleanability, and a metallic appearance. It can be appropriate for indoor equipment, general fabrication, food-related surroundings where the project specification permits it, and many mildly corrosive environments. However, the actual suitability depends on exposure to chlorides, acids, moisture, temperature, cleaning chemicals, and mechanical conditions.
SS304 is not a universal replacement for every stainless steel grade. Projects exposed to high chloride levels, coastal conditions, or aggressive chemicals may require a different material assessment, potentially including another stainless steel grade or a protective design approach. I advise buyers to provide the environmental details rather than selecting material by grade name alone.
A reliable inquiry should define more than “2.36 inch SS304 welded wire mesh panel.” The specification should identify the material, opening, wire diameter, panel dimensions, tolerance requirements, edge configuration, surface finish, quantity, packaging, and destination. If any item is omitted, suppliers may quote technically different products under the same keyword.
| Specification | What to Confirm | Why It Matters |
|---|---|---|
| Material | SS304, required mill documentation, and applicable standard | Supports material verification and project acceptance |
| Opening | 2.36 inch nominal size, approximately 60 mm, and measurement method | Controls screening, access, airflow, and visual appearance |
| Wire diameter | Required diameter and permitted tolerance | Influences stiffness, weight, and cost |
| Panel size | Length, width, squareness, and cutting requirements | Determines installation efficiency and shipping volume |
| Finish | Mill finish, cleaned surface, or other specified treatment | Affects appearance and downstream fabrication |
| Edges | Open ends, trimmed edges, framed edges, or bent details | Influences handling safety and assembly |
A 2.36 inch opening can be considered for partitions, equipment separation, storage areas, and general industrial barriers when the project’s access and safety requirements allow that opening size. The wire diameter and support frame should be selected together because the panel does not function independently from its fixing system. Buyers should confirm whether the finished guard must meet a specific machine-safety or workplace-safety requirement.
SS304 welded mesh panels can be cut, framed, bolted, clamped, or otherwise incorporated into fabricated assemblies, subject to the capabilities of the fabricator. The open grid allows visibility and ventilation while providing a defined physical structure. For racks, cages, and enclosures, I recommend checking point loads, unsupported spans, fastener spacing, and whether cut edges require additional protection.
Some buyers use stainless welded mesh for infill panels, screens, decorative structures, or protective covers where a clean metal appearance is desired. In these cases, visual consistency, panel flatness, weld appearance, and edge finishing may be as important as basic mesh dimensions. A production sample or approved finish reference can reduce disagreements during bulk supply.
For more information, please visit Shunqiang Wire Mesh.
Start with the purpose of the panel: containment, separation, guarding, ventilation, support, visibility, or appearance. Record the environmental exposure, expected contact, installation orientation, and required service conditions. This prevents a buyer from choosing a mesh solely because its opening matches a catalog description.
State the opening as both 2.36 inches and approximately 60 mm where relevant, then specify whether it is center-to-center or clear opening. Add wire diameter, panel dimensions, edge details, and hole or cutout locations if required. A simple dimensioned drawing is usually more useful than a short product name because it gives the supplier a common reference.
Confirm that SS304 is suitable for the operating environment and ask what material documentation can accompany the order. If the project requires a particular standard, inspection record, or traceability process, include it in the request for quotation. Do not assume that a stainless appearance alone proves the grade or that every supplier applies the same verification process.
Compare unit price, panel dimensions, wire diameter, packaging, loading quantity, delivery term, payment conditions, and any tooling or cutting charges. MOQ and lead time are normally quotation-dependent because they change with customization, raw material availability, production scheduling, and order volume. For planning, request a written production lead-time estimate and separate it from transportation time.
The cost of a 2.36 inch SS304 welded wire mesh panel is influenced by stainless steel consumption, wire diameter, panel size, welding configuration, finishing, packaging, and order quantity. A larger wire diameter generally requires more metal, but price should still be evaluated against the required performance rather than reduced by specification changes without engineering review. Freight can also vary significantly according to panel dimensions and packing method.
MOQ should be discussed together with the production format. Standard panels may be easier to schedule, while non-standard dimensions, special edges, or repeated cutouts may require additional setup and a higher minimum order. I recommend requesting two quotations when possible: one for a standard configuration and one for the exact customized configuration.
When evaluating a supplier, I look for the ability to interpret technical drawings, clarify ambiguous opening measurements, and provide a consistent production specification. The supplier should explain how wire diameter, panel size, welding arrangement, and edge treatment will be controlled. Clear communication before payment is often more valuable than a low price based on incomplete information.
At Shunqiang Wire Mesh, I approach this product as a specification-matching project rather than a keyword-only purchase. Our team can review the required opening, wire diameter, panel size, material grade, edge configuration, finish, quantity, and packing requirements before preparing a quotation. Where the specification is incomplete, we can identify the points that need confirmation instead of treating assumptions as final requirements.
For B2B buyers, useful support includes technical clarification, quotation preparation, drawing-based communication, production coordination, and export packing discussion. Any inspection, documentation, customization, MOQ, or lead-time commitment should be confirmed for the specific order. This approach helps align the purchased panel with the buyer’s fabrication process and destination requirements.
The best 2.36 inch SS304 welded wire mesh panel is not defined by the opening alone. It is the configuration that correctly combines approximately 60 mm spacing, verified SS304 material, suitable wire diameter, accurate panel dimensions, appropriate edges, and application-specific performance requirements. Buyers should also distinguish between nominal pitch and clear opening before approving a quotation.
My recommended next step is to send Shunqiang Wire Mesh a drawing or a structured inquiry stating the material, opening measurement method, wire diameter, panel size, quantity, finish, edge details, destination, and required documents. We can then review the specification and prepare a project-specific offer. This gives procurement teams a clearer basis for comparing suppliers and reduces the risk of receiving panels that match the product name but not the intended application.
Contact us to discuss your requirements of 2.36 inch ss304 welded wire mesh panel. Our experienced sales team can help you identify the options that best suit your needs.