AHF Active Harmonic Filter Selection Guide for Industrial Power Systems
To select an active harmonic filter (AHF), start with measured harmonic current at the point where correction is needed, then match the filter’s rated compensation current, voltage, phase configuration, and installation conditions to the application. Do not size an AHF from transformer capacity alone: the nonlinear loads, their operating patterns, and the harmonic limits your facility needs to meet all matter. At SINAVA, we recommend confirming these inputs before comparing models or requesting a quotation.
You can find more information on our web, so please take a look.
This guide is for industrial power-system buyers, electrical engineers, consultants, and procurement teams evaluating harmonic mitigation. It explains what an AHF does, how to assess application fit, which specifications to compare, and what information to prepare when approaching a supplier.
Key Takeaways
- Use site measurements and the required correction target to determine compensation capacity; transformer kVA alone is not a reliable sizing basis.
- Check system voltage, frequency, phase configuration, installation environment, and available space alongside rated current.
- Confirm whether the project needs harmonic mitigation only or also reactive power compensation and load balancing.
- Ask suppliers to clarify sizing assumptions, configuration, delivery scope, commissioning support, and warranty terms in writing.
How an Active Harmonic Filter Works
Basic concept
Nonlinear electrical loads draw current that is not a clean sinusoidal waveform. Common examples include variable-frequency drives, rectifiers, UPS systems, and other power-electronic equipment. This distorted current can contribute to voltage distortion, heating in electrical components, nuisance operation, and reduced power quality, depending on the system and operating conditions.
An AHF measures load current and uses power-electronic control to inject compensating current. The injected current is intended to reduce selected harmonic components at the chosen connection point. Unlike a passive filter designed around specific frequency characteristics, an active filter can respond dynamically to changing loads, subject to its control design and rated capacity.
Functions to verify
AHFs are commonly selected for harmonic current compensation, but some configurations also support reactive power compensation or load balancing. These functions are not interchangeable, and availability can vary by product and operating mode. Ask the supplier to state which functions are supported simultaneously and whether using one function affects capacity available for another.
Match the Filter to the Application
Identify the loads and operating pattern
List the major nonlinear loads, their rated power, control method, and expected operating schedule. A plant with drives operating steadily may have a different requirement from a facility where large loads start and stop frequently. Record whether the target is a single distribution panel, a group of loads, or the main bus, because the connection point affects what the filter can observe and compensate.
Where practical, obtain power-quality measurements under representative operating conditions. A survey can help identify harmonic current by order, total harmonic distortion, load variation, and existing voltage conditions. Measurements taken during a low-load period may not represent the demand that drives the filter selection.
Review the electrical system
Confirm nominal voltage, frequency, phase configuration, earthing arrangement, short-circuit conditions, and the available connection location. Industrial systems commonly operate at either 50 Hz or 60 Hz, but the actual project frequency and voltage must be specified rather than assumed. Also check enclosure requirements, ambient temperature, ventilation, dust, humidity, and the site’s installation restrictions.
Selection Framework: Specifications That Matter
1. Determine compensation current
Use measured harmonic current and the required reduction target to establish the needed compensation current. The AHF’s rated current is expressed in amperes, and the selected rating should account for the actual load profile and any operating margin required by the project design. As a simplified illustration only, if a survey identifies 120 A of harmonic current to address, an engineer would compare that requirement with the filter’s usable compensation capacity under the specified conditions; this example is not a universal sizing rule.
Ask the supplier to explain how the rating is applied when harmonic mitigation is combined with reactive compensation or load balancing. If multiple units are considered, clarify how they will be connected and controlled, and whether the proposed arrangement is intended for redundancy, capacity, or both.
SINAVA Product Page
2. Confirm voltage, phase, and connection
Verify that the model is designed for the system voltage and phase arrangement, and confirm whether it connects in parallel at the intended bus or panel. The supplier should identify any required external protection, disconnects, current transformers, cables, or other components. Do not assume that an AHF’s cabinet rating alone defines the complete installation scope.
3. Compare performance specifications carefully
Review the compensation range, supported harmonic orders, response behavior, control modes, overload behavior, and stated operating limits. Compare specifications using the same measurement point and operating assumptions. If a supplier provides a reduction percentage or performance guarantee, request the test conditions and confirm whether the figure applies to a particular harmonic, total distortion, or another defined metric.
4. Check installation and maintenance needs
Assess cabinet dimensions, mounting, airflow, clearances, access for maintenance, and the route for power and sensing connections. Confirm monitoring interfaces and alarms if integration with a plant control or energy-management system is required. A unit that meets the electrical specification still needs a practical installation plan and safe access for inspection.
Common Selection Mistakes
- Sizing from transformer capacity alone: Transformer kVA does not show the harmonic current produced by the connected loads or the correction target.
- Using unrepresentative measurements: A snapshot that misses peak or variable operating conditions can lead to an unsuitable rating.
- Comparing headline percentages without context: Ask what was measured, where it was measured, and under which load conditions.
- Ignoring combined functions: Reactive power compensation or balancing may use part of the unit’s available capacity, depending on its design.
- Leaving installation scope unclear: Confirm protection, sensing, wiring, commissioning responsibilities, and site requirements before ordering.
Pricing, MOQ, and Lead-Time Considerations
AHF pricing depends on factors such as rated current, voltage, cabinet configuration, functions, communications, and project-specific requirements. A quotation may also be affected by the number of units, accessories, inspection requirements, packaging, and delivery destination. Request an itemized scope so that proposals can be compared on equivalent terms.
Minimum order quantity and lead time are supplier- and configuration-dependent; they should be confirmed for the requested model rather than assumed from a general product description. For project planning, ask for the current production schedule, required technical approvals, shipping terms, and any commissioning or after-sales service options. We at SINAVA can review the application information and discuss a suitable configuration and quotation based on the project scope.
Supplier Evaluation Checklist
Before placing an order, ask the supplier to document the proposed model’s ratings and operating limits. Request clarification on how the sizing was derived, what assumptions were used, and which project requirements remain unverified. Confirm the warranty terms, technical documentation, spare-parts approach, delivery scope, and support available during installation or commissioning.
For an apples-to-apples comparison, provide every shortlisted supplier with the same information: single-line diagram, system voltage and frequency, measured harmonic data, load schedule, target outcome, installation conditions, and required delivery date. If data is not yet available, state that clearly and ask whether a site survey or additional measurement is recommended. This helps separate a preliminary estimate from a design proposal based on verified project inputs.
Conclusion: Choose from Measurements, Not Assumptions
The right AHF for an industrial power system is the one whose compensation capacity, electrical ratings, functions, and installation requirements fit the measured load and the project’s power-quality objective. Begin with representative harmonic data, confirm the connection point and system conditions, and compare suppliers using documented assumptions rather than headline claims. This approach reduces the risk of under-sizing, over-specification, and scope gaps.
As a next step, prepare your system voltage and frequency, load list, harmonic measurement report if available, target compensation requirements, and site constraints. Share these details with SINAVA to discuss model selection, configuration, quotation, and delivery planning for your application.